STM32MP157 Linux系统移植开发篇17:Linux内核摄像头驱动移植

2021/9/17 7:08:52

本文主要是介绍STM32MP157 Linux系统移植开发篇17:Linux内核摄像头驱动移植,对大家解决编程问题具有一定的参考价值,需要的程序猿们随着小编来一起学习吧!

本文章为《STM32MP157 Linux系统移植开发篇》系列中的一篇,笔者使用的开发平台为华清远见FS-MP1A开发板(STM32MP157开发板)。stm32mp157是ARM双核,2个A7核,1个M4核,A7核上可以跑Linux操作系统,M4核上可以跑FreeRTOS、RT-Thread等实时操作系统,STM32MP157开发板所以既可以学嵌入式linux,也可以学stm32单片机。

针对FS-MP1A开发板,除了Linux系统移植篇外,还包括其他多系列教程,包括Cortex-A7开发篇、Cortex-M4开发篇、扩展板驱动移植篇、Linux应用开发篇、FreeRTOS系统移植篇、Linux驱动开发篇、硬件设计篇、人工智能机器视觉篇、Qt应用编程篇、Qt综合项目实战篇等。欢迎关注,更多stm32mp157开发教程及视频,可加技术交流Q群459754978,感谢关注。

关于FS-MP1A开发板:
手机淘宝分享码:复制本行文字打开手淘₤T4FPXn3YYJ2₤
链接:https://item.taobao.com/item.htm?id=622457259672

1.实验原理

DCMI(Digital Camera Interface),DCMI是一个同步并行接口,能够从外部8bit、10bit、12bit或14bit的CMOS摄像头接收高速数据流,支持不同的数据格式:YCbCr4:2:2/RGB565渐进式视频和压缩数据(JPEG)。

FS-MP1A可以外接8bit的COM Camera,接口定义如下:

接口与MPU管脚对应关系如下:

原理图网络编号对应管脚管脚功能管脚功能码
DCMI_D0PH9DCMI_D0AF13
DCMI_D1PH10DCMI_D0AF13
DCMI_D2PH11DCMI_D0AF13
DCMI_D3PH12DCMI_D0AF13
DCMI_D4PH14DCMI_D0AF13
DCMI_D5PI4DCMI_D0AF13
DCMI_D6PB8DCMI_D0AF13
DCMI_D7PE6DCMI_D0AF13
DCMI_RESETPA3GPIOANALOG
DCMI_PWDNPA4GPIOANALOG
DCMI_PIXCKPA6DCMI_PIXCLKAF13
DCMI_VSYNCPB7DCMI_VSYNCAF13
  1. DCMI设备树节点

参考文档:

Documentation/devicetree/bindings/media/st,stm32-dcmi.txt

Documentation/devicetree/bindings/media/video-interfaces.txt

内核中ST对STM32MP15x系列芯片的设备树资源了做了定义,可参见:

arch/arm/boot/dts/stm32mp151.dtsi

stm32mp151中dcmi定义如下:

dcmi: dcmi@4c006000 {

compatible = "st,stm32-dcmi";

reg = <0x4c006000 0x400>;

interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;

resets = <&rcc CAMITF_R>;

clocks = <&rcc DCMI>;

clock-names = "mclk";

dmas = <&dmamux1 75 0x400 0xe0000001>;

dma-names = "tx";

status = "disabled";

};

上述代码只对dcmi做了基本的初始化,并没有针对不同的硬件设计做适配,所以需结合硬件补全设备树节点信息。

参考帮助文档及内核中其它STM32MP157设备树中对于dcmi的定义,修改dcmi内容如下:

&dcmi {

status = "okay";

pinctrl-names = "default", "sleep";

pinctrl-0 = <&dcmi_pins_a>;

pinctrl-1 = <&dcmi_sleep_pins_a>;

port {

dcmi_0: endpoint {

remote-endpoint = <&ov5640_0>;

bus-width = <8>;

hsync-active = <0>;

vsync-active = <0>;

pclk-sample = <1>;

pclk-max-frequency = <77000000>;

};

};

};

由于stm32mp15-pinctrl.dtsi中对于DCMI管脚的定义与FS-MP1A实际使用管脚一致,所以无需修改

  1. CMOS Camera设备树节点

FS-MP1A支持多款COMS Camera,本节以ov5640为例:

参考文档:

Documentation/devicetree/bindings/media/i2c/ov5640.txt

参考帮助文档及内核中其它STM32MP157设备树中对于ov5640的定义,修改dcmi内容如下:

ov5640: camera@3c {

compatible = "ovti,ov5640";

reg = <0x3c>;

clocks = <&clk_ext_camera>;

clock-names = "xclk";

DOVDD-supply = <&v2v8>;

powerdown-gpios = <&gpioa 4 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;

reset-gpios = <&gpioa 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;

rotation = <180>;

status = "okay";

port {

ov5640_0: endpoint {

remote-endpoint = <&dcmi_0>;

bus-width = <8>;

data-shift = <2>; /* lines 9:2 are used */

hsync-active = <0>;

vsync-active = <0>;

pclk-sample = <1>;

pclk-max-frequency = <77000000>;

};

};

};

  1. 2.8V电源定义

前文已经说过如何添加电源节点,本节不再重复,在根节点添加&v2v8节点,内容如下:

v2v8_audio: regulator-v2v8 {

compatible = "regulator-fixed";

regulator-name = "v2v8";

regulator-min-microvolt = <2800000>;

regulator-max-microvolt = <2800000>;

regulator-always-on;

regulator-boot-on;

};

  1. 24M时钟定义

参考文档:

Documentation/devicetree/bindings/clock/fixed-clock.yaml

参考帮助文档或内核中其他设备树文件,对于时钟的定义,增加内容如下:

clocks {

clk_ext_camera: clk-ext-camera {

#clock-cells = <0>;

compatible = "fixed-clock";

clock-frequency = <24000000>;

};

};

2.实验目的

熟悉基于Linux操作系统下的摄像头设备驱动移植配置过程。

3.实验平台

华清远见开发环境,FS-MP1A平台;

4.实验步骤

  1. 导入交叉编译工具链

linux@ubuntu:$ source /opt/st/stm32mp1/3.1-openstlinux-5.4-dunfell-mp1-20-06-24/environment-setup-cortexa7t2hf-neon-vfpv4-ostl-linux-gnueabi

  1. 增加DCMI设备树节点

修改arch/arm/boot/dts/stm32mp15xx-fsmp1x.dtsi文件,在文件末尾添加如下内容:

&dcmi {

status = "okay";

pinctrl-names = "default", "sleep";

pinctrl-0 = <&dcmi_pins_a>;

pinctrl-1 = <&dcmi_sleep_pins_a>;

port {

dcmi_0: endpoint {

remote-endpoint = <&ov5640_0>;

bus-width = <8>;

hsync-active = <0>;

vsync-active = <0>;

pclk-sample = <1>;

pclk-max-frequency = <77000000>;

};

};

};

  1. 增加OV5640节点

修改arch/arm/dts/stm32mp15xx-fsmp1x.dtsi文件,在I2C5节点中添加OV5640设备信息,红色字体为增加内容:

&i2c5 {

pinctrl-names = "default", "sleep";

pinctrl-0 = <&i2c5_pins_a>;

……

ov5640: camera@3c {

compatible = "ovti,ov5640";

reg = <0x3c>;

clocks = <&clk_ext_camera>;

clock-names = "xclk";

DOVDD-supply = <&v2v8>;

powerdown-gpios = <&gpioa 4 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;

reset-gpios = <&gpioa 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;

rotation = <180>;

status = "okay";

port {

ov5640_0: endpoint {

remote-endpoint = <&dcmi_0>;

bus-width = <8>;

data-shift = <2>; /* lines 9:2 are used */

hsync-active = <0>;

vsync-active = <0>;

pclk-sample = <1>;

pclk-max-frequency = <77000000>;

};

};

};

};

  1. 增加2.8V电源和24M时钟

修改arch/arm/dts/stm32mp15xx-fsmp1x.dtsi文件,在根节点最后添加2.8V电源和24M时钟,红色字体为增加内容:

/ {

memory@c0000000 {

device_type = "memory";

reg = <0xc0000000 0x20000000>;

};

……

v2v8: regulator-2p8v {

compatible = "regulator-fixed";

regulator-name = "v2v8";

regulator-min-microvolt = <2800000>;

regulator-max-microvolt = <2800000>;

regulator-always-on;

regulator-boot-on;

};

clocks {

clk_ext_camera: clk-ext-camera {

#clock-cells = <0>;

compatible = "fixed-clock";

clock-frequency = <24000000>;

};

};

};

  1. 配置内核

配置内核支持ov5640,并列出主要选项,如下

linux@ubuntu:$ make menuconfig

Device Drivers --->

<*> Multimedia support --->

[*] V4L platform devices --->

<*> STM32 Digital Camera Memory Interface (DCMI) support

I2C Encoders, decoders, sensors and other helper chips --->

<*> OmniVision OV5640 sensor support

  1. 编译内核及设备树

linux@ubuntu:$ make -j4 uImage dtbs LOADADDR=0xC2000040

  1. 重启测试

将编译好的设备树和内核镜像拷贝到/tftpboot目录下,通过tftp引导内核,系统启动后启动信息中包含如下信息:

在屏幕的界面上选择“Camera preview”应用进入摄像头预览程序,启动界面后即可看到摄像头实时采集的图像。

硬件平台:华清远见FS-MP1A开发板(STM32MP157)

部分开发教程下载:加QQ群459754978,群文件里有。

部分视频课程收看:华清远见研发中心的个人空间_哔哩哔哩_Bilibili

淘宝购买链接:华清远见stm32mp157 linux开发板stm32单片机arm开发嵌入式学习板

手机淘宝分享码:复制本行文字打开手淘₤T4FPXn3YYJ2₤



这篇关于STM32MP157 Linux系统移植开发篇17:Linux内核摄像头驱动移植的文章就介绍到这儿,希望我们推荐的文章对大家有所帮助,也希望大家多多支持为之网!


扫一扫关注最新编程教程