基于redis集群设置密码的实例

2019/6/30 22:29:51

本文主要是介绍基于redis集群设置密码的实例,对大家解决编程问题具有一定的参考价值,需要的程序猿们随着小编来一起学习吧!

注意事项:

1.如果是使用redis-trib.rb工具构建集群,集群构建完成前不要配置密码,集群构建完毕再通过config set + config rewrite命令逐个机器设置密码

2.如果对集群设置密码,那么requirepass和masterauth都需要设置,否则发生主从切换时,就会遇到授权问题,可以模拟并观察日志

3.各个节点的密码都必须一致,否则Redirected就会失败

config set masterauth abc 
config set requirepass abc 
config rewrite 

测试版本:

redis3.0.7

测试环境:

centos7

集群规模:

3主3从

集群构建成功前的redis配置:

port 8000 
cluster-enabled yes 
cluster-config-file "nodes-8000.conf" 
cluster-node-timeout 15000 
dir "/opt/redisdata" 
appendonly yes 
appendfilename "appendonly-8000.aof" 
logfile "/opt/redisdata/8000.log" 
daemonize yes 
pidfile "/var/run/redis-8000.pid" 
dbfilename "dump-8000.rdb" 
cluster-require-full-coverage no 

集群构建成功后的redis配置:

port 8004 
cluster-enabled yes 
cluster-config-file "nodes-8004.conf" 
cluster-node-timeout 15000 
dir "/opt/redisdata" 
appendonly yes 
appendfilename "appendonly-8004.aof" 
logfile "/opt/redisdata/8004.log" 
daemonize yes 
pidfile "/var/run/redis-8004.pid" 
dbfilename "dump-8004.rdb" 
cluster-require-full-coverage no 
# Generated by CONFIG REWRITE 
requirepass "abc" 
masterauth "abc" 

测试:

1.8002是主,8005是8002的从,现在要kill掉8002模拟主从切换

2.查看8005的日志,8005最终被选举成新的master

21227:S 14 Jun 07:28:49.343 # Connection with master lost.
21227:S 14 Jun 07:28:49.343 * Caching the disconnected master state.
21227:S 14 Jun 07:28:49.433 * Connecting to MASTER 127.0.0.1:8002
21227:S 14 Jun 07:28:49.433 * MASTER <-> SLAVE sync started
21227:S 14 Jun 07:28:49.434 # Error condition on socket for SYNC: Connection refused
21227:S 14 Jun 07:28:50.437 * Connecting to MASTER 127.0.0.1:8002

21227:S 14 Jun 07:29:06.205 # Start of election delayed for 564 milliseconds (rank #0, offset 337).
21227:S 14 Jun 07:29:06.507 * Connecting to MASTER 127.0.0.1:8002
21227:S 14 Jun 07:29:06.507 * MASTER <-> SLAVE sync started
21227:S 14 Jun 07:29:06.507 # Error condition on socket for SYNC: Connection refused
21227:S 14 Jun 07:29:06.808 # Starting a failover election for epoch 10.
21227:S 14 Jun 07:29:06.810 # Failover election won: I'm the new master.
21227:S 14 Jun 07:29:06.810 # configEpoch set to 10 after successful failover
21227:M 14 Jun 07:29:06.810 * Discarding previously cached master state.

3.再次启动8002,查看8005的日志,8002已经变成8005的slave

21227:M 14 Jun 07:32:53.511 * Slave 127.0.0.1:8002 asks for synchronization
21227:M 14 Jun 07:32:53.511 * Full resync requested by slave 127.0.0.1:8002
21227:M 14 Jun 07:32:53.511 * Starting BGSAVE for SYNC with target: disk
21227:M 14 Jun 07:32:53.511 * Background saving started by pid 21613
21613:C 14 Jun 07:32:53.513 * DB saved on disk
21613:C 14 Jun 07:32:53.513 * RDB: 0 MB of memory used by copy-on-write
21227:M 14 Jun 07:32:53.612 * Background saving terminated with success
21227:M 14 Jun 07:32:53.612 * Synchronization with slave 127.0.0.1:8002 succeeded

4.简单测试了GET SET命令,正常

以上这篇基于redis集群设置密码的实例就是小编分享给大家的全部内容了,希望能给大家一个参考,也希望大家多多支持找一找教程网。



这篇关于基于redis集群设置密码的实例的文章就介绍到这儿,希望我们推荐的文章对大家有所帮助,也希望大家多多支持为之网!


扫一扫关注最新编程教程